learn to understand about the troubleshooting of hardware that has been installed and assembled into a computer or a PC is as it should be done, so if it appears the problem is not too upset about it.
Troubleshooting is the process of finding common mistakes that often occur in each of the hardware that is used when assembling a computer and find solutions to problems that occur.
Well, on this occasion, tried to write about specific troubleshooting on Casing and Power Supply. There are some troubleshooting cases Casing and Power Supply, including:
Case:
UPS can not handle stress well.
Solution:
Possible owned UPS, the batteries in a weak condition. Immediately refill the battery capacity and strength to become full again. If the battery is in a state of full, but the problem still occurs, then the problem most likely lies in the UPS.
Case:
Fan in power supply is not working or loud noises.
Solution:
Need to let go of power supply. Before you will be put back, clean the dust on the power supply by using equipment that is prepared to clean the dust. In clean conditions, the power supply will not be issued with noise and will work well.
Case:
Power supply noise rickety.
Solution:
Most likely the problem lies in the processor fan. Clean the processor fan. But if after cleaning is still experiencing the same conditions, then the problem lies in some electronic konrponen around power supply.
Case:
Dim lighting and reboot the computer.
Solution:
Possible voltage is unstable and requires UPS to handle the problem. Immediately buy UPS to handle the problem, because if left to the PC will be damaged over time due to unstable voltage.
Case:
When the computer, did not happen, but the power supply does not want to live.
Solution:
Make sure all components installed and connected to the power and getting power from the power supply. If we use a computer case with power supply type ATX, we must check the power switch connector from the Power Switch connector onto the motherboard. Very often, especially when installing compute case with ATX systems, connectors are installed wrong and causing terbali PC can not burn. If the connector is inserted correctly, then the problem lies in a bad power supply. Immediately replace the power supply with a new one.
Case:
Power Saving Mode or Standby in Windows 98 does not work properly.
Solution:
There are several components that cause the problems above, include the following:
1. Make sure the Power Management features are active. To activate it, do the following steps: Click Start / Settings / Control Panel / double click the Power Management icon Power schemes to ensure the conditions and set Always on the desired time to display power management activity on the monitor and hard disk.
2. Close all applications that are open and active. Follow the instructions on the Clean Boot to cover all software or programs that are open and active. Once the software is closed, the automatic facilities Power Saving / Standby will appear.
3. Screen Savers. Disable all screen savers. Screen savers are for example 3D Flower Box, 3D Flying Objects, 3D Maze and 3D Text. If this screen saver has lost the feature Power Saving / standby will appear.
4. Power Management On / Off in the CMOS. In general, computers have power management controls in the BIOS. CMOS check the computer to ensure that the Power Management is active in the CMOS. If it turns out there is a problem, then the possibility of the APM driver is damaged or corrupted.
5. Hardware components can cause mode Power Saving / Standby does not work with some hardware, for example, can cause mode USB Power Saving / Standby not working properly.
Troubleshooting is the process of finding common mistakes that often occur in each of the hardware that is used when assembling a computer and find solutions to problems that occur.
Well, on this occasion, tried to write about specific troubleshooting on Casing and Power Supply. There are some troubleshooting cases Casing and Power Supply, including:
Case:
UPS can not handle stress well.
Solution:
Possible owned UPS, the batteries in a weak condition. Immediately refill the battery capacity and strength to become full again. If the battery is in a state of full, but the problem still occurs, then the problem most likely lies in the UPS.
Case:
Fan in power supply is not working or loud noises.
Solution:
Need to let go of power supply. Before you will be put back, clean the dust on the power supply by using equipment that is prepared to clean the dust. In clean conditions, the power supply will not be issued with noise and will work well.
Case:
Power supply noise rickety.
Solution:
Most likely the problem lies in the processor fan. Clean the processor fan. But if after cleaning is still experiencing the same conditions, then the problem lies in some electronic konrponen around power supply.
Case:
Dim lighting and reboot the computer.
Solution:
Possible voltage is unstable and requires UPS to handle the problem. Immediately buy UPS to handle the problem, because if left to the PC will be damaged over time due to unstable voltage.
Case:
When the computer, did not happen, but the power supply does not want to live.
Solution:
Make sure all components installed and connected to the power and getting power from the power supply. If we use a computer case with power supply type ATX, we must check the power switch connector from the Power Switch connector onto the motherboard. Very often, especially when installing compute case with ATX systems, connectors are installed wrong and causing terbali PC can not burn. If the connector is inserted correctly, then the problem lies in a bad power supply. Immediately replace the power supply with a new one.
Case:
Power Saving Mode or Standby in Windows 98 does not work properly.
Solution:
There are several components that cause the problems above, include the following:
1. Make sure the Power Management features are active. To activate it, do the following steps: Click Start / Settings / Control Panel / double click the Power Management icon Power schemes to ensure the conditions and set Always on the desired time to display power management activity on the monitor and hard disk.
2. Close all applications that are open and active. Follow the instructions on the Clean Boot to cover all software or programs that are open and active. Once the software is closed, the automatic facilities Power Saving / Standby will appear.
3. Screen Savers. Disable all screen savers. Screen savers are for example 3D Flower Box, 3D Flying Objects, 3D Maze and 3D Text. If this screen saver has lost the feature Power Saving / standby will appear.
4. Power Management On / Off in the CMOS. In general, computers have power management controls in the BIOS. CMOS check the computer to ensure that the Power Management is active in the CMOS. If it turns out there is a problem, then the possibility of the APM driver is damaged or corrupted.
5. Hardware components can cause mode Power Saving / Standby does not work with some hardware, for example, can cause mode USB Power Saving / Standby not working properly.
No comments:
Post a Comment